Teac CD-RW750 Manuel d'utilisateur télécharger pdf (Page 15)

TASCAM CD-RW750 Owner’s Manual 15

3 – Playback operations

The CD-RW750 can be used to play back CDs

(including CD-R and CD-RW discs that have been

recorded and finalized on other types of recorder), as

well as CD-R discs and CD-RW discs that have been

recorded on the unit.

Simple playback operations

1 Press the OPEN/CLOSE key (3 or 1) to open

the disc tray.

2 Discs should be inserted in the tray with the

label uppermost.

3 Press the OPEN/CLOSE key (3 or 1) to close

the tray again.

When a disc is loaded into the unit, the display

briefly shows

TOC Reading., with a flashing

period following the word “Reading” as the unit

determines the contents of the disc. When the TOC

has been read, the display shows the total running

time of the disk, followed by the disc title (if the disc

contains CD TEXT information), followed by the

total running time.

If the title of the disc is more than 12 characters long

(a disc title can be up to 23 characters long), only the

first 12 characters are displayed.

The first 12 characters of the disc title are also shown

(for three seconds) when playback is stopped.

In stop mode, no digital output is possible (see “Input

monitoring” on page 18).

The CD-RW750 also shows (at the top left of the dis-

play) one of the following:

1 Press the PLAY key (I or L) to start play-

back

2 Press the STOP key (H or J) to stop play-

back

3 Press the PAUSE key (J or K) to pause play-

back temporarily.

The track number indicators at the bottom of the dis-

play light, to show the available unplayed tracks. If

there are thirteen tracks on the disc, for example,

indicators

through

will light. If there are more

than 20 tracks on a disc, the track number

OVER

indi-

cator (at the bottom of the display) will light.

Track titles If the finalized disc contains CD

TEXT information, the first 12 characters of the track

title (track titles can be up to 23 characters in length)

are shown for about two seconds, about three sec-

onds into the track.

Time display modes

When playing back a CD (or in pause mode), there

are five different display modes.

In each time mode, the current track number is given,

followed by the time, as given below, e.g.

0:48

Press the DISPLAY key (A or ) to cycle through

these time display modes, as described below:

NOTE

If programmed playback has been selected (“Pro-

grammed order playback” on page 17), the elapsed

time and total remaining time refer to the programmed

material, not the whole disc.

A commercial pre-recorded CD or a finalized

CD-R

CD-R, NO TOC

A CD-R which has yet to be finalized

CD-RW, NO TOC

A CD-RW which has yet to be finalized

CD-RW

A finalized CD-RW (this differs from a CD, as it

may be unfinalized and erased)

[blank]

Unusable or unreadable disc or no disc

Display shows Meaning

TOTAL

Total elapsed time of the disc

[blank]

Elapsed time of the current track

TOTAL REMAIN

Time remaining of the current disc

REMAIN

Time remaining of the current track

[track title]

If the disc contains CD TEXT information, the

current track title is shown. If the title is longer

than 12 characters, is scrolls across the display.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 29 30

Commentaires sur ces manuels

Pas de commentaire

Teac CD-RW750 Manuel d'utilisateur Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Audio Teac CD-RW750